MUL-20 PART#20-44 Die Holder Bearing Sold Individually but 2 are needed per tool This bander part is OEM

MUL-20 PART#20-25  Large Bearing This bander part is OEM

MUL-20 PART#20-41 Cutter Blade This part cuts the banding  It is common for this part to wear out causing it to to properly cut the banding. This is a common wear partThis bander part is OEM

MUL20 PART#20-19  Die Also known as the Punch, Steel banders punch a die cut to lock the banding.  This is considered a common wear part. The MUL-20 has a total of 3 dies per tool. These dies are reversible for double the life. This...

MUL20 PART#20-5  Knob     Sold Individually but 2 are needed per tool    This bander part is OEM     

MUL20 PART#20-66  Sealing HandleThis bander part is OEM

MUL20 PART#20-4  Tension HandleThis bander part is OEM

MUL20 PART#20-1  Ratchet Wheel Sold Individually but 2 are needed per tool  This bander part is OEM

MUL20 PART#20-22HT  Clutch Plug / Bottom Gripper Also known as the bottom gripper, This part holds the bottom strap from moving while the feedwheel tensions the strap. This is considered a common wear part. This bander part is OEM

MUL-20 PART#20-38HT Feedwheel/Tension wheel.This part pulls the banding tight and works with the gripper  to achieve tension on the banding. It is common for this part to wear out causing it to slip when tensioning the band. If the wheel just...

Replacement End Cover for Models # P320 & P322Part # P32.1238This part is genuine OEM.

Replacement Rocker for the Orgapack ORT200 / Signode BXT       NOTES- Battery must be removed from bander prior to service.

The MIP1400  Clutch Plug. The clutch plug and feedwheel are common wear parts for the MIP1400.

MIP1200  Gripper/Clutch Plug  This part holds the banding on the lower side of the tensioner. If the banding is "pulling through" the tensioner,  it is likely that this part needs replaced. It is a common wear part...

REPLACEMENT 18v BATTERY CHARGER FOR FROMM TOOLS For Models: P318 P326 P327 P328 P329 Voltage:18 Volts Ampere Hours (Ah or Amp Hours):N/A Chemistry:Lithium-Ion (Li-Ion) Time to charge:1.5 hours / 90 minutes Every battery that is purchased from us is...

Replacement knife/cutter for the Orgapack ORT300 & ORT400 battery bander.Replacement knife/cutter for the Signode BXT-H battery bander.Replacement knife/cutter for the Cyklop CHT300 battery bander.   This is a common wear part...

Replacement knife/cutter for the Orgapack ORT 200 & ORT250 battery bander. Replacement knife/cutter for the Signode BXT battery bander. This is a common wear part that, when worn, will not cut the banding completely off . Easy replacement...

Replacement Toothplate/Gripper for the Orgapack ORT400 battery bander.   This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The Toothplate/Gripper when worn will allow...

Replacement Toothplate/Gripper for the Orgapack ORT250 battery bander. This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The Toothplate/Gripper when worn will allow the lower piece of...

Replacement wheel for the Orgaoack ORT400 battery bander. This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The feedwheel will mill on the strap not allowing tensioning of the band. Easy...

Replacement wheel for the Orgapack ORT250 battery bander.   This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The feedwheel will mill on the strap not allowing tensioning of the band...

Li-Ion 14.4v and 18v replacement battery charger for the following tools: Orgapack ORT400 - ORT250 Orgapack ORT-130 ORT260 - ORT450 Signode BXT2-19 - BXT2-16 Signode BXT3-13 - BXT3-16 - BXT3-19 VT550L H45L H45A - H45B H46A - H46B -...

Li-Ion 18v 4.0Ah replacement battery for the following tools: Orgapack  ORT400 ORT450 Signode  BXT2-19 BXT3-19 Part # 2187.004 Sold elsewhere under: 2187.004 H-2386-BATT 428905

Li-Ion 14.4v OEM battery for the following tools: Orgapack  ORT250 Signode  BXT2 VT550L Part # 2187.002 Sold elsewhere under: 2187.002 H-2385-BATT 428866

Replacement Toothplate for the Signode BXT and the Orgapack ORT200   This is a common wear part that when worn, will cause the lower band to pull through the bander when tensioning the strap. Easy replacement only requires a #2...

MIP1300 Gripper/Clutch Plug  M1300-19This part holds the banding on the lower side of the tensioner. If the banding is "pulling through" the tensioner, it is likely that this part needs replaced. It is a common wear part and works...

Replacement Feedwheel for MIP 1200 and MIP1300 Strap Tensioners   This part pulls the banding tight and works with the gripper to achieve tension on the banding. It is common for this part to wear out causing it to slip when tensioning the band. If...

The MIP1400  feedwheel. The clutch plug and feedwheel are common wear parts for the MIP1400.

The MIP1620  feedwheel. This feedwheel is directional! M1620-18  

Replacement wheel for the Signode BXT-H, Cyklop CHT-300 and the Orgapack ORT-300   This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The feedwheel will mill on the strap not...

Replacement wheel for the Signode BXT and the Orgapack ORT200 This is a common wear part that, when worn, will not allow the banding to become tight when the button is pressed. The feedwheel will mill on the strap not allowing tensioning of the band...

PF-G is a pusher tensioner for steel strapping. Use with closed seals. 3/8" - 3/4" x up to 0.025in.

1/2" x .031" x 7,200' Polypropylene Strapping 600 lb break strength Black or Yellow

REGULAR DUTY PUSHER BAR TENSIONER The MIP-1800 is a regular duty, pusher bar tensioner for round or irregular surfaces. With an extremely small footprint, this tool is perfect for jobs where there isn't much work area, like hanging HVAC or Air Ducts...

Cut stretch film or string with this safe and easy to use cutter.   Prevents product damage from exposed blades.   Slide the edge over the stretch film and in one easy pull all of the film is cut way.   Packaged one per box.

These knives have a snap off  blade to allow a new cutting edge.   The blade length is adjustable with a push-lock sliding action.    

Deluxe knife with rubber grips. These knives have an 8 pt. snap off blade to allow a new cutting edge.   The blade length is adjustable with a push-lock sliding action.    

These knives have a snap off  blade to allow a new cutting edge.   The blade length is adjustable with a push-lock sliding action.    

5" x 80 Gauge x 1000' Extended Core Bundling FilmDisposable, 1" diameter handle is built into each roll. No dispenser required. Faster, easier and more economical to use than strapping, tape or twine. Use quiet, cast film to combine items for freight...

18" x 80 Gauge x 1500' Cast Hand Stretch FilmReduce warehouse noise with super quiet, quality Cast Hand Stretch Film. Use Colored Hand Stretched Film for product identification. Ultra clear film makes bar codes and other important information easy to...