Description
REGULAR DUTY PUSHER BAR TENSIONER
The UST-180 is a regular duty, pusher bar tensioner for round or irregular surfaces. With an extremely small footprint, this tool is perfect for jobs where there isn't much work area, like hanging HVAC or Air Ducts. Commonly referred to as the "Insulation tool" or "Insulators tool." Uses a gripper to hold the banding tight while the body rides the pusher bar to achieve tension.
Looking for replacement parts? Click Here
Strapping Dimension:
W: 3/8" - 3/4" (10mm to 19mm)
G: .015" to .023" (3.8mm to .58mm)
Weight:
4 lbs
Tension:
Limited tension capabilty, tool must be reracked to achieve higher tension. However, you cannot wear parts out by overtensioning like the a feedwheel tool
Speed:
N/A
Average seal strength:
Dependant on seal/sealer used
Strapping Dimension:
W: 3/8" - 3/4" (10mm to 19mm)
G: .015" to .023" (3.8mm to .58mm)
Weight:
4 lbs
Tension:
Limited tension capabilty, tool must be reracked to achieve higher tension. However, you cannot wear parts out by overtensioning like the a feedwheel tool
Speed:
N/A
Average seal strength:
Dependant on seal/sealer used
Seal and Joint type:
Pusher
Single Notch
Similar Tools:
Gerrard 1902-D
MIP1800
Acme B2A0
Looking for replacement parts? Click Here
Strapping Dimension:
W: 3/8" - 3/4" (10mm to 19mm)
G: .015" to .023" (3.8mm to .58mm)
Weight:
4 lbs
Tension:
Limited tension capabilty, tool must be reracked to achieve higher tension. However, you cannot wear parts out by overtensioning like the a feedwheel tool
Speed:
N/A
Average seal strength:
Dependant on seal/sealer used
Strapping Dimension:
W: 3/8" - 3/4" (10mm to 19mm)
G: .015" to .023" (3.8mm to .58mm)
Weight:
4 lbs
Tension:
Limited tension capabilty, tool must be reracked to achieve higher tension. However, you cannot wear parts out by overtensioning like the a feedwheel tool
Speed:
N/A
Average seal strength:
Dependant on seal/sealer used
Seal and Joint type:
Pusher
Single Notch
Similar Tools:
Gerrard 1902-D
Acme B2A0
Datasheets & Literature
Replacement Parts
Replacement Parts
- UST-180 180-10 Holding Dog Spring
- UST-180 180-8 Holding Dog
- UST-180 180-11 Holding Pawl Spring
- UST-180 180-5 Pop Rivet
- UST-180 180-9 Holding Dog Shaft
- UST-180 180-4 Ratchet Wheel
- UST-180 180-14 Pulling Pawl
- UST-180 180-16 Tension Lever
- UST-180 180-20 Set Screw
- UST-180 180-13 Release Handle
- UST-180 180-3 Pusher Bar
- MUST-180 180-6 Holding Pawl
- UST-180 180-12 Release Shaft
- UST-180 180-22 Cotter Pin
- UST-180 180-7 Holding Pawl Shaft
- UST-180 180-17 Dowel Pin
- UST-180 180-19 Lock Washer
- UST-180 180-18 Machine Screw
- UST-180 180-15 Tension Lever Shaft
- UST-180 Pusher Bar Tensioner Hardware Kit
Additional Information
Type: |
Tensioner |
Features: |
Complete Tool |
Operation: |
Manual |
For Use With: |
Steel |
Strap Size: |
1/2" |
Strap Size: |
5/8" |
Strap Size: |
3/4" |
